40Cr钢汽车半轴热处理工艺及淬火缺陷分析
摘要: 在这里不仅仅描述了40Cr钢的化学成分对钢的组织和性能的影响,还制定了40Cr钢件的正火、退火、淬火、回火、调质等热处理工艺,测量试样在进行各种热处理之后拥有的硬度和冲击韧性的大小,确定在经过热处理工艺后,试样是否产生缺陷,并且对此进行分析和改进,以便于适合此钢的工作环境。
关键词: 40Cr, 热处理工艺, 淬火缺陷。
40Cr steel car axle shaft heat treatment process and quenching defect analysis
Abstract: Not just describing the effect of the chemical composition of 40Cr steel on the microstructure and properties of steel, the positive fire of 40Cr steel parts is also developed. annealing, quenching, tempering, tempered heat treatment process, measuring the hardness and impact toughness of the specimen after all kinds of heat treatment, determine whether after the heat treatment process, the specimen has defects, and to analyze and improve, so that the working environment suitable for this steel。
Keywords: 40Cr Heat Treatment Process Quenching Defects
目 录
一、引言………………………………………………………………………… 2
二、合金调质钢的工作条件和失效形式……………………………………… 2
(一)、合金调质钢的工作条件…………………………………………………2
(二)、合金调质钢的失效形式…………………………………………………4
三、40Cr合金调质钢的组织和性能特点要求的分析…………………………4
(一)、40Cr合金调质钢的组织要求……………………………………………… 4
(二)、一般的合金调质钢的所拥有的性能上的要求…………………………… 6
(三)、40Cr合金调质钢所拥有的性能上的要求………………………………… 8
四、钢件的一般加工路线……………………………………………………… 8
(一)、预备热处理………………………………………………………………… 8
(二)、淬火工艺…………………………………………………………………… 9
(三)、回火工艺…………………………………………………………………… 13
五、40Cr钢汽车半轴热处理工艺的设计和分析…………………………… 13 (一)、分析………………………………………………………………………13
(二)、热处理工艺参数的选择……………………………………………………15
(三)、热处理工艺的制定…………………………………………………………15
六、40Cr钢汽车半轴的淬火缺陷分析………………………………………16
(一)、淬火缺陷的分析……………………………………………………………16
(二)、热处理工艺的改进…………………………………………………………17
七、结论……………………………………………………………………… 18
参考文献…………………………………………………………………………… 19
参考文献:
[1]、史美堂 ,《金属材料及热处理》 上海科学技术出版社 ,2001.
[2]、许德珠, 《机械工程材料》高等教育出版社 ,1992.
[3]、李方进, 《金属学与热处理》 机械工业出版社 ,1995.
[4]、戴起勋, 《金属材料学》 化学工业出版社 ,2005.
[5]、机械工程学会热处理学会,《热处理手册》,机械工业出版社,TG15-62/2 2008.
[6]、文九巴 ,《材料科学与工程》 哈尔滨工业大学出版社, 2007.
[7]、赵昌盛,《模具材料及热处理手册》 机械工业出版社,2008.
[8]、徐勇军,《工程材料基础与模具材料》化学工业出版社,2008
[9]、彭其凤、丁洪太,《热处理工艺及设计》上海交大出版社,1994
[10]、中国机械网
http://www.bysj360.com/html/5839.html
http://www.bysj360.com/html/6302.html