基于plc的弹体智能拧紧机控制系统设计
摘要:随着我国国防工业的发展,传统的国防机械制造难以满足日益增长的精度和信息要求,大多数依靠传统的手动装配是合乎逻辑的,但手动装配效率低下、不可靠,无法满足精确装配的技术要求,为了满足弹体数据的优化和计算机管理技术要求,成为国防工业中需要解决的问题。因此,本文主要关注的是断路器,首先是导言,然后是总体方案设计,然后是系统硬件,最后是软件。
关键词:弹体拧紧机;系统设计;PLC
Control System of Intelligent Tightening Machine
Abstract: With the emergence of China's national defense industry, the traditional assembly of national defense industrial machinery is difficult to meet the increasing accuracy and information requirements. It is reasonable to rely on the traditional manual fastening for the fastening of industrial defense projectiles, but the manual fastening has low efficiency and reliability, which can not meet the technical requirements of assembly accuracy. In order to meet the technical requirements of missile refinement and computerized management of missile data, the missile tightening machine has become an urgent problem to be solved in the national defense industry.
Based on this, this paper mainly studies the body tightening machine. First, the preface is discussed, then the overall scheme is designed, then the hardware system is designed, and finally the software is designed.
Keywords: body tightening machine; System design; PLC
目录
第一章 前言 1
第二章 弹体智能拧紧机控制系统总体方案设计 2
2.1弹体智能拧紧机工艺分析 2
2.1.1对象分析 4
2.1.2工艺流程 4
2.2 弹体智能拧紧机控制系统的控制要求 5
2.2.1 控制功能 5
2.2.2 技术指标 6
2.3 弹体智能拧紧机控制系统的设计 6
2.3.1 控制系统工作原理 6
2.3.2 控制系统总体框构 7
第三章 弹体智能拧紧机控制系统的硬件设计 9
3.1 弹体智能拧紧机控制设备选型 9
3.1.1 可编程控制器 9
3.1.2 工控机 10
3.1.3 伺服电机及驱动器 10
3.2 操作面板设计 11
3.3 弹体智能拧紧机控制系统的硬件电路设计 12
3.3.1 通讯连接 12
3.3.2 数字量输入输出 13
3.3.3 模拟量输入输出 15
3.3.4 伺服驱动器 16
3.3.5 光幕传感器 17
3.3.6 电源系统 18
第四章 弹体智能拧紧机控制系统的软件设计 20
4.1 下位机程序设计 20
4.1.1 控制器算法程序设计 20
4.1.2 弹体装配程序设计 24
4.1.3 参数设置设计 30
4.2 上位机程序设计 30
4.2.1 上位机编程软件简介 30
4.2.2 上位机操作界面描述 32
4.2.3 上位机操作界面设计 33
结论 39
参考文献 41
第一章 前言
压缩时未记录,无法提供初始记录以供以后检查。泵体在拧紧前必须进行预试验。拧紧过程需要很长时间,因此迫切需要优化泵体的拧紧过程,实现对泵体拧紧过程的自动化,最终实现对泵体拧紧过程的监控。本课题根据不同规格的弹体在拧紧时的设计,应检查拧紧力、拧紧力矩和压缩量,最后通过密封检查,因为弹体特性模型太多,但必须尽可能简化人员操作, 管理子弹数据和收紧过程,完成弹药装配过程中的卡箍控制设计,国防工业的研究重点是子弹拉伸质量控制、子弹拉伸质量评估和卡箍数量控制。
参考文献
[1] 姜维军. 螺栓拧紧曲线在分析拧紧质量问题中的应用[J]. 汽车维修,2010,07:21-23.
[2] 朱 正 德 , 林 湖 . 扭 矩 - 转 角 法 拧 紧 工 艺 条 件 下 的 装 配 质 量 评 价 [J]. 轻 型 汽 车 技
术,2004,09:26-30.
[3] Goel AK, De Silva Garza AG. Special issue on artificial intelligence in design. Journal of
Computing and Information Science in Engineering. 2010;10(3):30301.
[4] Trollhattan,Sweden.Controlled Tightening Over the Yield Point of a Screw Based on Taylor’s
Series Expansions. Journal of Pressure Vessel Technology.2003.November Volume 125,Issue
4,pp:460-466.
[5] Nassar SA, Alkelani AA. Effect of tightening speed on clamp load distribution in gasketed
joints. SAE Technical Papers. 2006.
[6] J. A. Martins,E. C. Romão,I. Ferreira,I. Kövesdy. The Influence of Method and Environment in
Torquing Screws Used in Bucket Wheel to Stacker-Reclaimer Machine[J]. Journal of Failure
Analysis and Prevention,2012,124:.
[7] French Inventors Develop Wrench with Controlled Tightening. US Fed News Service,
Including US State News. 2006.
[8] 李国钧. 自动拧紧机原理分析及改进[J]. 汽车实用技术,2010,03:94-96.
[9] 黄恭伟. 自动螺纹拧紧机的控制系统设计[J]. 滁州学院学报,2008,03:61-64.
[10] 马英广. 发动机螺栓拧紧技术的研究[D].哈尔滨工程大学,2006.
[11] 黄健. 汽车装配自动拧紧机[D].上海交通大学,2008.
[12] 卫道柱. 螺纹自动拧紧机的研制[D].合肥工业大学,2004.
[13] 发动机螺栓连接及拧紧工具应用技术[D] 姜立华 - 《吉林大学》
[14] 螺母拧紧机项目融资商业计划书(专业版)
[15] 江骏,刘志峰,任永强,林巨广 基于IPC的自动拧紧机控制系统设计[D] ,2006.