Fanuc0i数控加工中心速度倍率PMC控制的运行与调试
摘要
数控系统中很多的功能都采用PMC程序实现,本毕业设计根据机床的速度倍率开关的功能要求设计电气原理图和接口电路,比如快速移动速度倍率、手轮速度倍率、进给速度倍率和主轴速度倍率的控制等,使用FANUC LADDER-Ⅲ软件编写梯形图,最后上机调试并修改、排除故障。
关键词:数控机床,加工中心,PMC控制。
Abstract
Many of the functions of CNC system using PMC program, this graduation design according to the switching rate of machine design of the functional requirements of the electrical schematic diagram and interface circuit, such as fast moving control rate, the hand wheel speed ratio, feed rate and spindle speed ratio, the use of FANUC LADDER- software programming the ladder diagram, finally the machine debug and modify, troubleshooting.
Keywords: CNC machine tools, machining centers, PMC control
目录
摘要 II
Abstract III
目录 IV
第一章 绪论 1
1.1 课题的研究背景 1
1.2 设计内容 2
第二章 速度倍率开关原理图及接口设计 3
2.1快速移动倍率 3
2.1.1 接口信号的定义 3
2.1.2 电气原理图的设计 4
2.2手轮速度倍率 4
2.2.1 接口信号的定义 4
2.2.2电气原理图设计 5
2.3进给速度倍率 6
2.3.1接口信号的定义 6
2.3.2电气原理图设计 6
2.4主轴速度倍率 7
2.4.1接口信号 7
2.4.2电气原理图的设计 7
第三章 FANUC LADDER-Ⅲ软件的使用 9
3.1 LADDER-Ⅲ软件的启动 9
3.3 FANUC LADDER-Ⅲ软件窗口功能 9
3.3.1 LADDER-Ⅲ图标 9
3.3.2 LADDER-Ⅲ界面 10
3.3.3编写PMC程序 10
3.3.4.编写界面 11
3.4 FANUC LADDER-Ⅲ的PMC编译功能 12
3.4.1编译PMC程序 12
3.4.2导出PMC程序 13
3.4.3转存PMC程序 14
第四章 基于FANUC LADDER-Ⅲ速度倍率梯形图的设计 15
4.1 快速移动倍率设计 15
4.2 手轮速度倍率设计 15
4.3 进给倍率设计 15
4.4 主轴倍率设计 17
第五章 速度倍率PMC梯形图调试 19
5.1 导入PMC梯形图 19
5.2 调试PMC程序 20
5.2.1快速移动速度倍率调试 20
5.2.2进给速度倍率调试 22
总结 24
致谢 25
参考文献 26
参考文献
1.罗敏、FANUC数控系统PMC编程技术 北京 化学工业出版社 2013
2.曹智军、肖龙 数控PMC编程与调试 北京 清华大学出版社 2010
3.周兰、陈少艾 数控系统连接调试与PMC编程 北京 机械工业出版社 2012
4.刘永久 数控机床故障诊断与维修技术 北京 机械工业出版社2009
http://www.bylw520.net/html/2200.html http://www.bysj360.com/ http://www.bysj360.com/html/1358.html http://www.caddown.com/