订书机底座冲压成型工艺与模具设计(模具毕业设计)
摘要:本文在分析其工艺性的基础上,根据生产要求,确定采用先落料冲孔拉伸打苞切舌,再撕边翻孔。本设计主要是落料凸、凹模及冲孔凸、凹模的设计,还有就是弯曲所要考虑的变形等等。需要计算凸凹模的间隙、工作零件的尺寸和公差。此外,还需要确定模具工艺零件和结构零件以及模具的总体尺寸,然后根据上面的设计绘出模具的总装图。
关键词:模具;冲裁件;凸模;凹模 ;切舌;孔翻边
Design of Progressive Die pad
Abstract: The pad core board which belongs to the typical punching parts, based on the analysis of theprocess, according to the production requirements, determine the structure of progressive die. This design is mainly the design of blanking punch, die and punch, die gap, the working parts, need to calculate the dimensions and tolerances of convex and concave die. In addition, also need to determine the overall size of mold parts and structural parts and mold,and then according to the design drawing mold assembly diagram above.
Keywords: die; stamping die; mould;
目 录
1.绪 论 1
1.1 课题研究的目的和意义 1
1.2 课题国内外研究概况 1
1.3 课题研究的主要内容 2
2.冲压工艺设计 4
2.1 冲压件简介 4
2.2 冲压零件的工艺性分析 5
2.3冲裁工艺方案的确定 5
2.4模具的整体方案 6
3.落料尺寸计算 8
3.1毛坯尺寸的确定及排样 8
3.2落料凸凹模刃口尺寸计算 9
3.3 确定其搭边值 11
3.4 确定排样图 12
3.5 凸、凹模刃口尺寸的确定 14
4.压力机选择 18
4.1计算总压力 18
4.2选择压力机 18
5.压力中心计算 19
5.1拉深部凸凹模尺寸计算 19
5.2圆孔翻边工艺方案及计算 20
结论与展望 22
小结与致谢 23
参考文献 24
参考文献
[1]高晓康 陈于萍.互换性与测量技术[M] 北京:高等教育出版社,2009.1
[2]成虹.冲压工艺与模具设计(第二版)[M].北京:高等教育出版社,2006.
[3]翁其金.冷冲压技术(第二版)[M].北京:机械工业出版社,2011.
[4]宋满仓.冲压模具设计[M].北京:电子出版社,2010.
[5]郑家贤. 冲压模具设计指导[M].北京:机械工业出版社.2008
[6]胡佳秀. 简明机械零件设计手册(第二版)[M].北京:机械工业出版社.2012.5
[7]华红芳. 孙燕华. 机械制图及零部件测绘[M].北京.电子工业出版社,2012.8
[8]王孝培. 冲压手册(第二版)[M].北京.机械工业出版社
[9]王孝培. 冲压手册(第三版)[M].北京.机械工业出版社.2011.7